產品名稱：美國帕斯菲達pulsafeeder電磁計量泵LPK3MB-PTC1

LPK2M4B-KTC1，LPK2M4B-KTC1，LPB2M4B-KTC1，LPB2M4B-KTC1，LPD3M4B-KTC1，LPD3M4B-KTC1，LPF4M4B-KTC1，LPF4M4B-KTC1，

LPH4M4B-KTC1，LPH4M4B-KTC1，LPD4M4B-KTC1，LPD4M4B-KTC1，LPG4M4B-KTC1，LPG4M4B-KTC1，LPK5M4B-pTC3，LPK5MB-KTC3，

LPH5MB-PTC3，LPH5MB-KTC3，LPH5MB-KTC3，LPA3M4B-KTC1，LPA3M4B-KTC1，LPK3M4B-KTC1，LPK3M4B-KTC1，LPB4M4B-KTC1，

LPK7M4B-KTC3，LPH7M4B-PTC3， LPH7M4B-KTC3，LVH7MB-WTSK*，LPJ8MB-PTCB*，LPH8MB-PTCB*

?所有型號標配: 三功能閥,注射閥, 底閥, 進出口軟管（標*的型號無三功能閥） ?電源:220V*大功率:300W
?配五功能閥需單獨訂貨
?PVC泵頭可選，價格與PP泵頭材質相同.

美國帕斯菲達pulsafeeder電磁計量泵LPK3MB-PTC1，加藥泵流量調節方式：4-20MA+液位信號控制，泵頭材質：PP
*手動:頻率，沖程同時可調 *流量0.5-95升/小時，壓力2-21Bar *自動：可選4-20mA4-20MA信號，液位信號接收功能 *21種機型
美國帕斯菲達pulsafeeder電磁計量泵LPK3MB-PTC1，加藥泵流量調節方式：4-20MA+液位信號控制，泵頭材質：PP

5.5.1 停止功能（僅LP、LV、LB、LC型號）
泵的運行可以通過外部信號輸入停止。當外部信號輸入到標記O為的終端（位于控制盤 底部）時，O指示燈 （紅色）點亮，泵停止運行。停止功能超馳手動設定值和外部輸入。小心 L從同一觸點閉合運行多臺泵會損壞泵的電路。如果要求這類運行，必須使用多觸點控制繼電器或相似方法使泵的電路之間互相電氣隔離。
? 輸入信號必須以機械繼電器或其他機械丿「關裝置，或固態繼電器或其他固態開關裝置 的閉合形式。禁止使用電壓信號無論機械或固態裝置的開關電阻，ON（打開）時必 須為100歐姆或以下, OFF （關閉）時必須為1兆歐或以上。如果使用固態型裝置， 在:裝置有要求時，極性安裝必須正確：泄漏電流不能超過200毫安，以防止在：“OFF” 狀態時的誤觸發。停止功能通常與儲罐浮動開關一起使用。浮動開關觸點常開，但是當儲罐液位降到低于某 一點時，觸點閉合，泵停止運行。
5.5.2 外部調步功能（僅僅 LP、 LV、 LB、 LC 型號）泵的行程速率可以由外 部信號輸入控制。當連接輸入信號線路，“外部 /斷開 /手動”開關處于外部位置，且向標有的終端輸入觸點信號時，泵完成-次排放行程。

PULSAtron Series E Plus Metering Pump

General Description
Pulsafeeder PULSAtron Series E Plus chemical metering pumps are positive displacement, diaphragm type pumps. Output volume is adjustable while pumps are in operation from zero to maximum capacity. The PULSAtron Series E Plus contains a highly reliable timing circuit as well as circuit protection against voltage and current upsets. This pump features solenoid protection by thermal overload with auto-reset. The Series E Plus guided check valves, with their state-of-the-art seat and ball designs, provide precise seating, and excellent priming and suction lift characteristics. Our timing circuit is highly reliable and, by design, virtually unaffected by temperature, EMI and other electrical disturbances.
Pump Controls
Adjustment is by means of readily accessible dial knobs, one for changing stroke length and the other for changing stroke frequency. Both knobs are located opposite the liquid handling end. Automatic control via 4-20mA DC and stop function inputs. Auto-Off-Manual switch.
Drive Assembly
The pump drive is totally enclosed with no exposed moving parts. Electronics are housed in chemical resistant enclosure at the rear of the pump for maximum protection against chemical spillage. Average electrical power consumption is 130 Watts.
Materials of Construction
See Specifications tab. Chemical metering pump housing shall be of chemically resistant PBT thermoplastic. All exposed fasteners are stainless steel. Valve seat and seal ring are renewable by replacing the cartridge valve assembly.

Pulsafeeder PULSAtron Series E Plus Chemical Metering Pump - Key Features

• Manual Control by on-line adjustable stroke rate and stroke length.
• Highly Reliable timing circuit.
• Circuit Protection against voltage and current upsets.
• Panel Mounted Fuse.
• Solenoid Protection by thermal overload with auto-reset.
• Water Resistant, for outdoor and indoor applications.
• Indicator Lights, panel mounted.
• Guided Ball Check Valve Systems, to reduce back flow and enhance outstanding priming characteristics.
• Few Moving Parts and Wall Mountable.
• Safe & Easy Priming with durable leak-free bleed valve assembly (standard).
• Reliable metering performance.
• Rated "hot" for continuous duty.
• Leak-free, sealless, liquid end.

Includes:

A weighted foot valve/strainer assembly, a 1/2" NPT male injection fitting/back pressure check valve assembly, 4' suction tubing, 8' discharge tubing and Owners Manual